# Stepper motor buzzing not turning

**URL:** <https://forum.arduino.cc/t/stepper-motor-buzzing-not-turning/1390149>\
**Category:** Motors, Mechanics, Power and CNC\
**Created:** [June 20, 2025, 5:58pm UTC](https://forum.arduino.cc/t/stepper-motor-buzzing-not-turning/1390149 "2025-06-20T17:58:05Z")\
**Posts on this page:** 11\
**Page:** 1

<div class="post-metadata">

**Author:** ![wilsonintexas](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/wilsonintexas/32/1013044_2.png) [@wilsonintexas](https://forum.arduino.cc/u/wilsonintexas)\
**Post date:** [June 20, 2025, 5:58pm UTC](https://forum.arduino.cc/t/stepper-motor-buzzing-not-turning/1390149/1 "2025-06-20T17:58:05Z")

</div>

I am using a usongshine tb6600 motor driver  
Toggles set for 200 steps  
4 amps  
Powered from a 19v compter supply plenty of power  
It is wired  
vcc + from power supply  
gnd – from power supply but then jumpers to pul -, dir +, dir -, ena+, ena-, and connected to arduino ground  
dir+ is connected to pin 7 of arduin  
note I grounded direction as part of debug, I really do not care what direction it goes.  
a+ is black  
a- is green  
b+ is red  
b- is blue  
I try running this program to debug the issue

same result two differnt steppers

```arduino
const int stepPin = 5;
const int dirPin = 7;

void setup() {
  pinMode(stepPin, OUTPUT);
  pinMode(dirPin, OUTPUT);

  digitalWrite(dirPin, HIGH); // try LOW if needed
}

void loop() {
  digitalWrite(stepPin, HIGH);
  delayMicroseconds(500);
  digitalWrite(stepPin, LOW);
  delayMicroseconds(500);
}type or paste code here

```

---

<div class="post-metadata">

**Author:** ![wilsonintexas](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/wilsonintexas/32/1013044_2.png) [@wilsonintexas](https://forum.arduino.cc/u/wilsonintexas)\
**Post date:** [June 20, 2025, 6:01pm UTC](https://forum.arduino.cc/t/stepper-motor-buzzing-not-turning/1390149/2 "2025-06-20T18:01:30Z")

</div>

I did check the stepper with an ohm meter, black to green is 1.8 ohm red to blue is same. I also tried switching green abd black, but no change. if it were working i expected direction to change.

---

<div class="post-metadata">

**Author:** ![Paul\_KD7HB](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/paul_kd7hb/32/1127958_2.png) [@Paul\_KD7HB](https://forum.arduino.cc/u/Paul_KD7HB)\
**Post date:** [June 20, 2025, 8:23pm UTC](https://forum.arduino.cc/t/stepper-motor-buzzing-not-turning/1390149/3 "2025-06-20T20:23:25Z")

</div>

> [@wilsonintexas](#):
>
> ```arduino
> void loop() {
> digitalWrite(stepPin, HIGH);
> delayMicroseconds(500);
> digitalWrite(stepPin, LOW);
> delayMicroseconds(500);
> 
> ```

Don't you think that 500 microseconds between steps is a bit too fast for a stepper to move?

---

<div class="post-metadata">

**Author:** ![anon94801460](https://avatars.discourse-cdn.com/v4/letter/a/278dde/32.png) [@anon94801460](https://forum.arduino.cc/u/anon94801460)\
**Post date:** [June 20, 2025, 8:31pm UTC](https://forum.arduino.cc/t/stepper-motor-buzzing-not-turning/1390149/4 "2025-06-20T20:31:00Z")

</div>

> [@wilsonintexas](#):
>
> ```arduino
> void loop() {
> digitalWrite(stepPin, HIGH);
> delayMicroseconds(500);
> digitalWrite(stepPin, LOW);
> delayMicroseconds(500);
> }
> 
> ```

This nonsense comes up nearly every day. Where do people get the idea that a stepper should run at 1000 steps/second from standstill?

---

<div class="post-metadata">

**Author:** ![gilshultz](https://avatars.discourse-cdn.com/v4/letter/g/67e7ee/32.png) [@gilshultz](https://forum.arduino.cc/u/gilshultz)\
**Post date:** [June 20, 2025, 10:15pm UTC](https://forum.arduino.cc/t/stepper-motor-buzzing-not-turning/1390149/5 "2025-06-20T22:15:16Z")

</div>

Look at it this way, you war crawling before walking before running. Systems are the same way and have limitations. Start slow!

Doing some background and technical research on parts you plan on using is always advisable.

---

<div class="post-metadata">

**Author:** ![LarryD](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/larryd/32/215550_2.png) [@LarryD](https://forum.arduino.cc/u/LarryD)\
**Post date:** [June 21, 2025, 1:40am UTC](https://forum.arduino.cc/t/stepper-motor-buzzing-not-turning/1390149/6 "2025-06-21T01:40:11Z")

</div>

- As an experiment, read the voltage from a potentiometer voltage divider.  
Use this value to set delay(. . .), adjust potentiometer for different delay times.

Example:  
Code for 100ms and shorter.

---

<div class="post-metadata">

**Author:** ![jw\_r](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/jw_r/32/1113755_2.png) [@jw\_r](https://forum.arduino.cc/u/jw_r)\
**Post date:** [June 21, 2025, 4:51am UTC](https://forum.arduino.cc/t/stepper-motor-buzzing-not-turning/1390149/7 "2025-06-21T04:51:47Z")

</div>

@wilsonintexas Here you can find more information about the operation of stepper motors:

> **[In-Depth: Control 28BYJ-48 Stepper Motor with ULN2003 Driver & Arduino](https://lastminuteengineers.com/28byj48-stepper-motor-arduino-tutorial/)**
>
> Learn to control 28BYJ-48 stepper motor and uln2003 driver with Arduino, working, gear ratio, pinout, wiring, arduino code and to control two steppers simultaneously

> **[Control Unipolar & Bipolar Steppers with L293D Motor Driver IC & Arduino](https://lastminuteengineers.com/stepper-motor-l293d-arduino-tutorial/)**
>
> Learn to control Unipolar & Bipolar Steppers with L293D along with H-bridge Working, Wiring, Arduino code for speed & direction control of 28BYJ-48, NEMA 17

Good luck with your project!

---

<div class="post-metadata">

**Author:** ![TomGeorge](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/tomgeorge/32/215261_2.png) [@TomGeorge](https://forum.arduino.cc/u/TomGeorge)\
**Post date:** [June 21, 2025, 8:08am UTC](https://forum.arduino.cc/t/stepper-motor-buzzing-not-turning/1390149/8 "2025-06-21T08:08:06Z")

</div>

Hi,

Can you please post a copy of your circuit, a picture of a hand drawn circuit in jpg, png?  
Hand drawn and photographed is perfectly acceptable.  
Please include ALL hardware, power supplies, component names and pin labels.

Can you post some images of your project?  
So we can see your component layout.

Thanks.. Tom.... 😃 👍 ☕ 🇦🇺

---

<div class="post-metadata">

**Author:** ![Wawa](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/wawa/32/1211303_2.png) [@Wawa](https://forum.arduino.cc/u/Wawa)\
**Post date:** [June 21, 2025, 9:53am UTC](https://forum.arduino.cc/t/stepper-motor-buzzing-not-turning/1390149/9 "2025-06-21T09:53:43Z")

</div>

@jw_r Those "LastMinute Engineers" pages are terrible.  
Who would recommend a dinosaur L293 brushed DC motor driver for a Nema 17 stepper motor without pointing out that you can only sort-off do that for high impedance motors, which most modern steppers are not. Besides that, Nema 17 tells us only the size of the mounting plate, nothing else.  
Leo..

---

<div class="post-metadata">

**Author:** ![jw\_r](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/jw_r/32/1113755_2.png) [@jw\_r](https://forum.arduino.cc/u/jw_r)\
**Post date:** [June 21, 2025, 11:57am UTC](https://forum.arduino.cc/t/stepper-motor-buzzing-not-turning/1390149/10 "2025-06-21T11:57:21Z")

</div>

Hello @Wawa, Thank you. I will gladly accept that from you. It is not possible for me to judge that. My knowledge does not extend far enough for that 🙂

The reason why I placed the link was because this article gives a nice description of the operation of a stepper motor. Greetings Jan-Willem

---

<div class="post-metadata">

**Author:** ![system](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/system/32/1140315_2.png) [@system](https://forum.arduino.cc/u/system)\
**Post date:** [December 18, 2025, 11:57am UTC](https://forum.arduino.cc/t/stepper-motor-buzzing-not-turning/1390149/11 "2025-12-18T11:57:35Z")

</div>

Closed on December 18, 2025, 11:57am UTC

This topic was automatically closed 180 days after the last reply. New replies are no longer allowed.
