the selected serial port _ does not exist or your board is not connected

avrdude: Version 6.3-20190619
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch

     System wide configuration file is "C:\Users\polio\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino17/etc/avrdude.conf"

     Using Port                    : COM3
     Using Programmer              : wiring
     Overriding Baud Rate          : 115200
     AVR Part                      : ATmega2560
     Chip Erase delay              : 9000 us
     PAGEL                         : PD7
     BS2                           : PA0
     RESET disposition             : dedicated
     RETRY pulse                   : SCK
     serial program mode           : yes
     parallel program mode         : yes
     Timeout                       : 200
     StabDelay                     : 100
     CmdexeDelay                   : 25
     SyncLoops                     : 32
     ByteDelay                     : 0
     PollIndex                     : 3
     PollValue                     : 0x53
     Memory Detail                 :

                              Block Poll               Page                       Polled
       Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
       ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
       eeprom        65    10     8    0 no       4096    8      0  9000  9000 0x00 0x00
       flash         65    10   256    0 yes    262144  256   1024  4500  4500 0x00 0x00
       lfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
       hfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
       efuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
       lock           0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
       calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
       signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

     Programmer Type : Wiring
     Description     : Wiring
     Programmer Model: AVRISP
     Hardware Version: 15
     Firmware Version Master : 2.10
     Vtarget         : 0.0 V
     SCK period      : 0.1 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.02s

avrdude: Device signature = 0x1e9801 (probably m2560)
avrdude: reading input file "C:\Users\polio\AppData\Local\Temp\arduino_build_142487/7segmentdigital.ino.hex"
avrdude: writing flash (9824 bytes):

Writing | ################################################## | 100% 1.57s

avrdude: 9824 bytes of flash written
avrdude: verifying flash memory against C:\Users\polio\AppData\Local\Temp\arduino_build_142487/7segmentdigital.ino.hex:
avrdude: load data flash data from input file C:\Users\polio\AppData\Local\Temp\arduino_build_142487/7segmentdigital.ino.hex:
avrdude: input file C:\Users\polio\AppData\Local\Temp\arduino_build_142487/7segmentdigital.ino.hex contains 9824 bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 1.24s

avrdude: verifying ...
avrdude: verification error, first mismatch at byte 0x0268
0xcc != 0xcd
avrdude: verification error; content mismatch

avrdude done. Thank you.

the selected serial port
does not exist or your board is not connected

This topic was automatically closed 180 days after the last reply. New replies are no longer allowed.