Uploading problem on the leonardo

Hi last week my Leonardo was working fine and now i get this error message whenever I upload any sketch.

Arduino: 1.8.5 (Windows 10), Board: "Arduino Leonardo"



avrdude: ser_recv(): read error: The I/O operation has been aborted because of either a thread exit or an application request.


avrdude: butterfly_recv(): programmer is not responding

avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: ser_drain(): read error: The device does not recognize the command.


avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_send(): write error: sorry no info avail

avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
Found programmer: Id = "&"; type = @
    Software Version = À.u; Hardware Version = “.ð
avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: error: buffered memory access not supported. Maybe it isn't
a butterfly/AVR109 but a AVR910 device?
avrdude: initialization failed, rc=-1
         Double check connections and try again, or use -F to override
         this check.

avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: error: programmer did not respond to command: leave prog mode
avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: error: programmer did not respond to command: exit bootloader

avrdude done.  Thank you.

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-objcopy" -O ihex -j .eeprom --set-section-flags=.eeprom=alloc,load --no-change-warnings --change-section-lma .eeprom=0  "C:\Users\Nick\AppData\Local\Temp\arduino_build_739455/Blink.ino.elf" "C:\Users\Nick\AppData\Local\Temp\arduino_build_739455/Blink.ino.eep"
"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-objcopy" -O ihex -R .eeprom  "C:\Users\Nick\AppData\Local\Temp\arduino_build_739455/Blink.ino.elf" "C:\Users\Nick\AppData\Local\Temp\arduino_build_739455/Blink.ino.hex"
Sketch uses 4128 bytes (14%) of program storage space. Maximum is 28672 bytes.
Global variables use 149 bytes (5%) of dynamic memory, leaving 2411 bytes for local variables. Maximum is 2560 bytes.
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, COM16, } => {}
PORTS {COM8, COM9, COM16, } / {COM8, COM9, } => {}
PORTS {COM8, COM9, } / {COM8, COM9, COM13, } => {COM13, }
Found upload port: COM13
C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega32u4 -cavr109 -PCOM13 -b57600 -D -Uflash:w:C:\Users\Nick\AppData\Local\Temp\arduino_build_739455/Blink.ino.hex:i 

avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM13
         Using Programmer              : avr109
         Overriding Baud Rate          : 57600
         AVR Part                      : ATmega32U4
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PA0
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    20     4    0 no       1024    4      0  9000  9000 0x00 0x00
           flash         65     6   128    0 yes     32768  128    256  4500  4500 0x00 0x00
           lfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           lock           0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : butterfly
         Description     : Atmel AppNote AVR109 Boot Loader

Connecting to programmer: .avrdude: butterfly_recv(): programmer is not responding

avrdude: butterfly_recv(): programmer is not responding

also my board is recognized in devise manager, but not any programs, like ableton live. Did I buy a faulty board?

(deleted)

Ah, really thank you. I was using TX and RX pins on Arduino. I will unplug them. Thanks!

I did this and got no changes. I must have posted error messages from my attempt to upload via HC-05 Bluetooth port. This is my serial port upload error message

avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM8
         Using Programmer              : avr109
         Overriding Baud Rate          : 57600
         AVR Part                      : ATmega32U4
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PA0
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    20     4    0 no       1024    4      0  9000  9000 0x00 0x00
           flash         65     6   128    0 yes     32768  128    256  4500  4500 0x00 0x00
           lfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           lock           0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : butterfly
         Description     : Atmel AppNote AVR109 Boot Loader

Connecting to programmer: .avrdude: butterfly_recv(): programmer is not responding

avrdude: butterfly_recv(): programmer is not responding
avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The I/O operation has been aborted because of either a thread exit or an application request.


avrdude: butterfly_recv(): programmer is not responding
avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
Found programmer: Id = "&"; type = @
    Software Version = æ.u; Hardware Version = “.ð
avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: ser_send(): write error: sorry no info avail
the selected serial port avrdude: butterfly_recv(): programmer is not responding
 does not exist or your board is not connected
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: error: buffered memory access not supported. Maybe it isn't
a butterfly/AVR109 but a AVR910 device?
avrdude: initialization failed, rc=-1
         Double check connections and try again, or use -F to override
         this check.

avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: error: programmer did not respond to command: leave prog mode
avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: error: programmer did not respond to command: exit bootloader

avrdude done.  Thank you.

It froze at the first

Connecting to programmer: .avrdude: butterfly_recv(): programmer is not responding

and after 10 mins i hit reset.

Is avrdude a program on the chip? i think maybe this knock off has the wrong microchip perhaps? idk

avrdude: error: buffered memory access not supported. Maybe it isn't
a butterfly/AVR109 but a AVR910 device?