When you try to select the avaliable ports in order to compile the code it won't show you any avaliable port for you to choose. It works well in windows 10 that's why I know it's not the esp8266 and not the cable. When you try to compile the code this is the error: FileNotFoundError: [Errno 2] No …

Bus 002 Device 003: ID 04f3:009c Elan Microelectronics Corp. Touchscreen Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 10f1:1a52 Importek TOSHIBA Web Camera - HD Bus 001 Device 003: ID 0…

Hi @redserpent . Are you experiencing some problem you would like assistance with? If so, please provide a detailed description of the problem you are having. Include the following information: What did you do? What were the results you expected from doing that thing? What were the results you obs…

I disabled 'brltty' :slight_smile: $ sudo systemctl mask brltty-udev.service [sudo] password for xxxx: Created symlink /etc/systemd/system/brltty-udev.service → /dev/null. $ systemctl stop brltty.service $ systemctl disable brltty.service ........ problem persists sudo dmesg | tail --lines=2…

i suspect that this line account for the system trying to communicate with the Arduino UNO: [598193.056891] usb 3-2.3: ch341-uart converter now attached to ttyUSB0

Hello I think it would be more efficient to disable the brltty device udev rule . But I don't know what version of ubuntu you're using. Have a look in this thread : Bug #1958224 “brltty claiming cp210x devices on 22.04” : Bugs : brltty package... * Impact The brltty udev rules are c…

I'm having the same problem. I've removed and purged brltty, no help. My system works with a UNO but not a Leanardo. When I attach the Leanardo and run dmesg I get, Blockquote[139066.234422] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready [139232.632206] usb 1-2.1.2: new full-speed U…

Hi @pommie . From the dmesg output, it looks like the Leonardo board is not recognized by the operating system at all (which is different from the other reports here where it was recognized but then interfered with by BRLTTY). Please try this experiment and then report back with the results: …

When I press reset, the orange LED marked L flashes and then stays on for ~6 seconds, then goes off and stays off.

OK, great. I'm going to ask you to run the dmesg command from the command line again and post the output. This time I want you to reset the board before running dmesg, according to the instructions below. :exclamation: This procedure is not intended to solve the problem. The purpose is to gather m…

Next step. Connect the Leonardo to the PC. Tap the reset button. Run lsusb. Do you see a board? If not, you're more than likely using a chrge-only cable. Try different cables.

Ubuntu arduino IDE not showing any ports

Development Tools IDE 1.x

Topic		Replies	Views
Trouble with Ubuntu Arduino IDE 2.3.4: No ports discovered IDE 2.x	3	305	September 1, 2025
"dev/ttyUSB0" port option greyed out Uploading	14	507	February 18, 2025
Stop the Unplug-Plug Dance: com-com Identifies Your Boards Instantly General Discussion	36	242	March 21, 2026
Unable to upload code to arduino only getting /dev/ttyS0 on Port IDE 1.x	9	4321	May 24, 2022
Arduino IDE often gets confused when more than one Arudion is connected to a PC IDE 2.x	63	290	January 26, 2026

Ubuntu arduino IDE not showing any ports

Related topics