i have the same line of code for forward and backward as you can see,, but.. when i run my motors using remote, it moves clearly doing what i expect but just for forward movement,, and for backward movement it only just move 1 motor.. i have pointed where that line is supposedly to work but not.. …

void Backward(){ digitalWrite(in2, LOW); digitalWrite(in4, LOW); digitalWrite(in1, HIGH); digitalWrite(in3, HIGH); analogWrite(en2, 100); analogWrite(en4, 100); } void Forward(){ digitalWrite(in1, LOW); digitalWrite(in3, LOW); digitalWrite(in2, HIGH); digitalWrite(in4, HIGH); a…

don't know why its still that one wheel not turning, and those analogwrites should be below the specific inputs, if i put that two below it wont work ... it shouldve been but not.. changed to void still that one wheel..

do you have the following in your code? // Define motor control pins const int in1 = 2; const int in2 = 3; const int in3 = 4; const int in4 = 5; const int en1 = 6; const int en2 = 7; const int en3 = 8; const int en4 = 9; // Set all motor control pins as outputs pinMode(in1, OUTPUT); pinMode(…

[image] okers: int in1=3; int in2=5; int in3=6; int in4=9; int en2 = 5; int en4 = 9; int en1 = 3; int en3 = 6; shouldn't there be 6 separate pins: EN1, EN2, IN1, IN2, IN3 and IN4. Each motor controlled by 2 IN pins and 1 EN pin and as Delta_G said, a separate pin for the IR receiver …

[image] okers: int in2=5; [image] okers: int en2 = 5; [image] okers: int in3=6; [image] okers: int en3 = 6; i wonder why it works at all

[image] Make experienced users help: two ways to quickly post code as a code-section Tutorials Hi newcomer, This thread wants to show you how you can speed-up getting helpful answers with small effort. If you manage at least to post this way. You have the sym…

this is the diagram i copied (this has 4 motors but im only using 2) [Remote Control Car] then again when going backward,, only one wheel is rotating after putting analogwrite .. but when there is no analogwrite written the two wheel works..

the driver board you're using has only 4 control pins: ENA, IN1/IN2, IN3/IN4, ENB. IN1/IN2 controls the direction when LOW/HIGH. You need to define only in1, in3, en1 and en2 to match the connections to the board [L298N-Motor-Driver-Module-Pinout] your code would be int Backward() { digita…

[image] okers: this is the diagram i copied (this has 4 motors but im only using 2) I´m not that sure 2xAA batteries (3V) will be enough to power this setup...

in1 connected to pin 3 in2 connected to pin 5 in3 connected to pin 6 in4 connected to pin 9 (pin is the arduino) so going back.. my code for backward is. void Backward() { digitalWrite(in1,HIGH); analogWrite(en1, 85); <--- can be also (in1, 85) digitalWrite(in3,HIGH); analogWrite(en3,…

Only one motor is rotating

Projects Programming

StefanL38 August 23, 2024, 6:18pm 17

Topic		Replies	Views
DC Motor only turns one direction but not the other General Electronics	69	1036	August 5, 2024
DC motor met IC besturing Nederlands	70	400	November 23, 2025
Add <IRremote> to library General Guidance	23	372	May 28, 2026
Gleichstrommotor tut nicht ganz was er soll_Aussetzer_falsche Richtung Deutsch	32	349	July 11, 2025
BTS7960-M behaves weirdly after using it in if condition General Guidance	14	248	April 4, 2024

Only one motor is rotating

Related topics