probleme de televersement

Quand je veux televerser mon programme il y a cela qui apparait :c une idée de comment je peux resoudre le probleme
avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch

System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

Using Port : COM4
Using Programmer : arduino
Overriding Baud Rate : 115200
AVR Part : ATmega328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :

Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack


eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00

Programmer Type : Arduino
Description : Arduino
Hardware Version: 3
Firmware Version: 4.4
Vtarget : 0.3 V
Varef : 0.3 V
Oscillator : 28.800 kHz
SCK period : 3.3 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.00s

avrdude: Device signature = 0x1e950f (probably m328p)
avrdude: reading input file "C:\Users\PC\AppData\Local\Temp\arduino_build_704379/pulse_sensor.ino.hex"
avrdude: writing flash (1916 bytes):

Writing | ################################################## | 100% 0.31s

avrdude: 1916 bytes of flash written
avrdude: verifying flash memory against C:\Users\PC\AppData\Local\Temp\arduino_build_704379/pulse_sensor.ino.hex:
avrdude: load data flash data from input file C:\Users\PC\AppData\Local\Temp\arduino_build_704379/pulse_sensor.ino.hex:
avrdude: input file C:\Users\PC\AppData\Local\Temp\arduino_build_704379/pulse_sensor.ino.hex contains 1916 bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 0.24s

avrdude: verifying ...
avrdude: 1916 bytes of flash verified

avrdude done. Thank you.

Reading | ################################################## | 100% 0.24s

avrdude: verifying ...
avrdude: 1916 bytes of flash verified

avrdude done. Thank you.

Ou est le problème ?

avrdude: verifying ...
avrdude: 1916 bytes of flash verified [/quote]
Cela veut dire que le programme transféré dans la flash du micro est conforme au fichier hex --> donc c'est bon

avrdude done. Thank you.
avrdude te dis qu'il a terminé et te dit merci de l'avoir utilisé :grin:

Si tu veux te rassurer charge le programme blink.
Modifie la valeur dans les deux delay() , met 100 puis 500 puis 2000 par exemple.
Charge le programme à chaque modification et vérifie que la fréquence de clignotement de la diode change bien.