Sketch not uploading

Development Tools Uploading
1 
Arduino: 1.8.18 (Windows 10), Board: "Arduino Uno"

Sketch uses 1122 bytes (3%) of program storage space. Maximum is 32256 bytes.

Global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes for local variables. Maximum is 2048 bytes.

Sketch uses 1122 bytes (3%) of program storage space. Maximum is 32256 bytes.

Global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes for local variables. Maximum is 2048 bytes.

avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00

avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x00

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x00

avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x00

avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x00

avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x00

avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x00

avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x00

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x00

Problem uploading to board.  See https://support.arduino.cc/hc/en-us/sections/360003198300 for suggestions.



This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
Arduino: 1.8.18 (Windows 10), Board: "Arduino Uno"

Sketch uses 1122 bytes (3%) of program storage space. Maximum is 32256 bytes.

Global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes for local variables. Maximum is 2048 bytes.

Sketch uses 1122 bytes (3%) of program storage space. Maximum is 32256 bytes.

Global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes for local variables. Maximum is 2048 bytes.

avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00

avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x00

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x00

avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x00

avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x00

avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x00

avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x00

avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x00

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x00

Problem uploading to board.
pls can somebody help me

2
  1. Anything connected to pins 0 and 1? Disconnect.
  2. Anything else connected? Disconnect.
  3. Are you indeed using an Uno? If so, is it the R3?
  4. Did you select the correct port?
    • Does that port disappear from the IDE when you disconnect the board?
    • What does Windows device manager think of your board? Is it correctly recognised?
  5. Is it an original Arduino? Or a clone?
    • Please provide a link to the board that you bought if not sure.
3

No nothing is connected
The ic ,i borrowed from my friend
Yes i think is original
Atmega8a controller
It is original as my checkings
It is r3 as it had 2 l2s pins beside the aref pins and also atmega16ua chip
It had a code in it which runs properly
P.S the code utilizes the 5 analog pins as output
We actually took the chip from the board and put it in smaller pcb
And we took it back and this happens
windows identifies as arduino UNO(com9)

4

This topic was automatically closed 180 days after the last reply. New replies are no longer allowed.