ATmega328P U burning bootloader

[crownous]

Hi, I would like to burn a bootloader on my ATmega328P. I have connected everything according to this picture:

but I keep getting an error:

Arduino: 1.8.19 (Windows 10), Vývojová deska: "Arduino Uno"

C:\Users\marti\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino17/bin/avrdude -CC:\Users\marti\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino17/etc/avrdude.conf -v -patmega328p -cstk500v1 -PCOM9 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0xFD:m -Uhfuse:w:0xDE:m -Ulfuse:w:0xFF:m 



avrdude: Version 6.3-20190619

         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/

         Copyright (c) 2007-2014 Joerg Wunsch



         System wide configuration file is "C:\Users\marti\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino17/etc/avrdude.conf"



         Using Port                    : COM9

         Using Programmer              : stk500v1

         Overriding Baud Rate          : 19200

         AVR Part                      : ATmega328P

         Chip Erase delay              : 9000 us

         PAGEL                         : PD7

         BS2                           : PC2

         RESET disposition             : dedicated

         RETRY pulse                   : SCK

         serial program mode           : yes

         parallel program mode         : yes

         Timeout                       : 200

         StabDelay                     : 100

         CmdexeDelay                   : 25

         SyncLoops                     : 32

         ByteDelay                     : 0

         PollIndex                     : 3

         PollValue                     : 0x53

         Memory Detail                 :



                                  Block Poll               Page                       Polled

           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack

           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------

           eeprom        65    20     4    0 no       1024    4      0  3600  3600 0xff 0xff

           flash         65     6   128    0 yes     32768  128    256  4500  4500 0xff 0xff

           lfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00

           hfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00

           efuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00

           lock           0     0     0    0 no          1    0      0  4500  4500 0x00 0x00

           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00

           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00



         Programmer Type : STK500

         Description     : Atmel STK500 Version 1.x firmware

         Hardware Version: 2

         Firmware Version: 1.18

         Topcard         : Unknown

         Vtarget         : 0.0 V

         Varef           : 0.0 V

         Oscillator      : Off

         SCK period      : 0.1 us



avrdude: AVR device initialized and ready to accept instructions



Reading | ################################################## | 100% 0.02s



avrdude: Device signature = 0x000000 (retrying)



Reading | ################################################## | 100% 0.02s



avrdude: Device signature = 0x000000 (retrying)



Chyba při vypalování zavaděče.

Reading | ################################################## | 100% 0.02s



avrdude: Device signature = 0x000000

avrdude: Yikes!  Invalid device signature.

         Double check connections and try again, or use -F to override

         this check.





avrdude done.  Thank you.

[jim-p]

There is a loose or bad connection on the braedboard.
Try taking the 328P out of the IC socket and plugging it directly into the breadboard

[crownous]

Yeah, I thought of that later, too. The problem was that the pins on the socket were too short to connect reliably to the board.

[jim-p]

So does it now work?

[crownous]

Yes, it works.

[jim-p]

Have FUN!

[crownous]

Thanks