I got a problem with my arduino plate. It has no pins to get into DFU mode. Long time wondering what i can do. Find this guide: Clone Arduino DFU Mode , however it's not help me. I get a message that boot sucsecfully done, but plate still was avilable only as USB serial Port. Interesting this - i can not anymore upload scetch in Arduino, when i boot Arduino-usbserial-uno.hex file - it's just not working, "avrdude: stk500_recv(): programmer is not responding", but it's not important. All i want is UnoJoy work, to make Shifter and Clutch for my race game.
That's what CMD said:
E:\shift\UnoJoyWin\ATmega8u2Code\HexFiles\joy>E:\shift\arduino-nightly\hardware\tools\avr/bin/avrdude -CE:\shift\arduino-nightly\hardware\tools\avr/etc/avrdude.conf -v -patmega328p -cstk500v1 -PCOM4 -b19200 -Uflash:w:UnoJoy.hex:i
avrdude: Version 6.3-20190619
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "E:\shift\arduino-nightly\hardware\tools\avr/etc/avrdude.conf"
Using Port : COM4
Using Programmer : stk500v1
Overriding Baud Rate : 19200
AVR Part : ATmega328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : STK500
Description : Atmel STK500 Version 1.x firmware
Hardware Version: 2
Firmware Version: 1.18
Topcard : Unknown
Vtarget : 0.0 V
Varef : 0.0 V
Oscillator : Off
SCK period : 0.1 us
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.02s
avrdude: Device signature = 0x1e950f (probably m328p)
avrdude: safemode: lfuse reads as FF
avrdude: safemode: hfuse reads as DE
avrdude: safemode: efuse reads as FD
avrdude: NOTE: "flash" memory has been specified, an erase cycle will be performed
To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "UnoJoy.hex"
avrdude: writing flash (2778 bytes):
Writing | ################################################## | 100% 3.12s
avrdude: 2778 bytes of flash written
avrdude: verifying flash memory against UnoJoy.hex:
avrdude: load data flash data from input file UnoJoy.hex:
avrdude: input file UnoJoy.hex contains 2778 bytes
avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 1.72s
avrdude: verifying ...
avrdude: 2778 bytes of flash verified
avrdude: safemode: lfuse reads as FF
avrdude: safemode: hfuse reads as DE
avrdude: safemode: efuse reads as FD
avrdude: safemode: Fuses OK (E:FD, H:DE, L:FF)
avrdude done. Thank you.