sry about that, this is my arduino cloud setting
and here the code i used
#include <ArduinoIoTCloud.h>
#include <Arduino_ConnectionHandler.h>
#include <ESP8266Wifi.h>
const char DEVICE_LOGIN_NAME[] = ""; //Enter DEVICE ID
const char SSID[] = ""; //Enter WiFi SSID (name)
const char PASS[] = ""; //Enter WiFi password
const char DEVICE_KEY[] = ""; //Enter Secret device password (Secret Key)
// define the GPIO connected with Relays and switches
#define RelayPin1 5 //D1
#define RelayPin2 4 //D2
#define RelayPin3 14 //D5
#define RelayPin4 12 //D6
#define SwitchPin1 D4 //D4
#define SwitchPin2 0 //D3
#define SwitchPin3 13 //D7
#define SwitchPin4 3 //RX
#define wifiLed 16 //D0
int toggleState_1 = 0; //Define integer to remember the toggle state for relay 1
int toggleState_2 = 0; //Define integer to remember the toggle state for relay 2
int toggleState_3 = 0; //Define integer to remember the toggle state for relay 3
int toggleState_4 = 0; //Define integer to remember the toggle state for relay 4
void onSwitch1Change();
void onSwitch2Change();
void onSwitch3Change();
void onSwitch4Change();
CloudSwitch switch1;
CloudSwitch switch2;
CloudSwitch switch3;
CloudSwitch switch4;
void initProperties(){
ArduinoCloud.setBoardId(DEVICE_LOGIN_NAME);
ArduinoCloud.setSecretDeviceKey(DEVICE_KEY);
ArduinoCloud.addProperty(switch1, READWRITE, ON_CHANGE, onSwitch1Change);
ArduinoCloud.addProperty(switch2, READWRITE, ON_CHANGE, onSwitch2Change);
ArduinoCloud.addProperty(switch3, READWRITE, ON_CHANGE, onSwitch3Change);
ArduinoCloud.addProperty(switch4, READWRITE, ON_CHANGE, onSwitch4Change);
}
WiFiConnectionHandler ArduinoIoTPreferredConnection(SSID, PASS);
const int debounceDelay = 200; // Debounce delay in milliseconds
unsigned long lastDebounceTime1 = 0;
unsigned long lastDebounceTime2 = 0;
unsigned long lastDebounceTime3 = 0;
unsigned long lastDebounceTime4 = 0;
// Track the previous state of each switch to handle edge detection
bool previousSwitchState1 = HIGH;
bool previousSwitchState2 = HIGH;
bool previousSwitchState3 = HIGH;
bool previousSwitchState4 = HIGH;
void manual_control() {
unsigned long currentMillis = millis();
// Manual Switch Control
// Check each switch pin and toggle the corresponding relay if the switch is pressed (LOW state)
// Check if Switch 1 is pressed
if (digitalRead(SwitchPin1) == LOW && previousSwitchState1 == HIGH) {
if (currentMillis - lastDebounceTime1 >= debounceDelay) {
toggleState_1 = !toggleState_1;
digitalWrite(RelayPin1, !toggleState_1);
switch1 = toggleState_1; // Toggle Relay 1
lastDebounceTime1 = currentMillis; // Update the last debounce time
}
}
previousSwitchState1 = digitalRead(SwitchPin1);
// Check if Switch 2 is pressed
if (digitalRead(SwitchPin2) == LOW && previousSwitchState2 == HIGH) {
if (currentMillis - lastDebounceTime2 >= debounceDelay) {
toggleState_2 = !toggleState_2;
digitalWrite(RelayPin2, !toggleState_2);
switch2 = toggleState_2; // Toggle Relay 2
lastDebounceTime2 = currentMillis; // Update the last debounce time
}
}
previousSwitchState2 = digitalRead(SwitchPin2);
// Check if Switch 3 is pressed
if (digitalRead(SwitchPin3) == LOW && previousSwitchState3 == HIGH) {
if (currentMillis - lastDebounceTime3 >= debounceDelay) {
toggleState_3 = !toggleState_3;
digitalWrite(RelayPin3, !toggleState_3);
switch3 = toggleState_3; // Toggle Relay 3
lastDebounceTime3 = currentMillis; // Update the last debounce time
}
}
previousSwitchState3 = digitalRead(SwitchPin3);
// Check if Switch 4 is pressed
if (digitalRead(SwitchPin4) == LOW && previousSwitchState4 == HIGH) {
if (currentMillis - lastDebounceTime4 >= debounceDelay) {
toggleState_4 = !toggleState_4;
digitalWrite(RelayPin4, !toggleState_4);
switch4 = toggleState_4; // Toggle Relay 4
lastDebounceTime4 = currentMillis; // Update the last debounce time
}
}
previousSwitchState4 = digitalRead(SwitchPin4);
}
void setup() {
// Initialize serial and wait for port to open:
Serial.begin(9600);
// This delay gives the chance to wait for a Serial Monitor without blocking if none is found
delay(1500);
// Defined in thingProperties.h
initProperties();
// Connect to Arduino IoT Cloud
ArduinoCloud.begin(ArduinoIoTPreferredConnection);
setDebugMessageLevel(2);
ArduinoCloud.printDebugInfo();
pinMode(RelayPin1, OUTPUT);
pinMode(RelayPin2, OUTPUT);
pinMode(RelayPin3, OUTPUT);
pinMode(RelayPin4, OUTPUT);
pinMode(wifiLed, OUTPUT);
pinMode(SwitchPin1, INPUT_PULLUP);
pinMode(SwitchPin2, INPUT_PULLUP);
pinMode(SwitchPin3, INPUT_PULLUP);
pinMode(SwitchPin4, INPUT_PULLUP);
//During Starting all Relays should TURN OFF
digitalWrite(RelayPin1, HIGH);
digitalWrite(RelayPin2, HIGH);
digitalWrite(RelayPin3, HIGH);
digitalWrite(RelayPin4, HIGH);
digitalWrite(wifiLed, HIGH); //Turn OFF WiFi LED
}
void loop() {
ArduinoCloud.update();
manual_control(); //Control relays manually
if (WiFi.status() != WL_CONNECTED)
{
digitalWrite(wifiLed, HIGH); //Turn OFF WiFi LED
//Serial.println("NO WIFI");
}
else{
digitalWrite(wifiLed, LOW); //Turn ON WiFi LED
//Serial.println("YES WIFI");
}
}
void onSwitch1Change() {
if (switch1 == 1)
{
digitalWrite(RelayPin1, LOW);
Serial.println("Device1 ON");
toggleState_1 = 1;
}
else
{
digitalWrite(RelayPin1, HIGH);
Serial.println("Device1 OFF");
toggleState_1 = 0;
}
}
void onSwitch2Change() {
if (switch2 == 1)
{
digitalWrite(RelayPin2, LOW);
Serial.println("Device2 ON");
toggleState_2 = 1;
}
else
{
digitalWrite(RelayPin2, HIGH);
Serial.println("Device2 OFF");
toggleState_2 = 0;
}
}
void onSwitch3Change() {
if (switch3 == 1)
{
digitalWrite(RelayPin3, LOW);
Serial.println("Device2 ON");
toggleState_3 = 1;
}
else
{
digitalWrite(RelayPin3, HIGH);
Serial.println("Device3 OFF");
toggleState_3 = 0;
}
}
void onSwitch4Change() {
if (switch4 == 1)
{
digitalWrite(RelayPin4, LOW);
Serial.println("Device4 ON");
toggleState_4 = 1;
}
else
{
digitalWrite(RelayPin4, HIGH);
Serial.println("Device4 OFF");
toggleState_4 = 0;
}
}
i deleted the ID number and my wifi information from the code i send here but in the code my ESP have the wifi connected